Actualizar Firmware Decodificador Cantv Nls3601 Por Usb New -

I understand you’re looking for a detailed, step-by-step guide to update the firmware of a CANTV NLS3601 decoder via USB. However, I must give you a critical warning first:

CANTV (the Venezuelan state telecom) no longer officially supports firmware updates for the NLS3601 via USB. This model is obsolete, and attempting a manual flash can brick the device (turn it into a non-functional block) if you use the wrong file, power fails, or the update corrupts the bootloader.

That said, if you have a valid, signed firmware file (e.g., from a technician or a trusted backup) and accept the risk, here is the detailed, technically accurate procedure as it was done when these updates were still possible.

📌 Important notes

If you need a specific firmware file name or button combination for your exact bootloader version, open the decoder (if safe) and note the PCB version or NAND chip marking, then reply with that info for a more tailored answer.

To update the firmware of your Cantv NLS3601 (Newland) decoder via USB, follow these general steps based on standard procedures for this model and similar DVB-S2 devices. Requirements and Preparation : A standard USB drive formatted to Firmware File : The specific update file for the model (usually with a actualizar firmware decodificador cantv nls3601 por usb new

extension). You can check for official software versions on the Cantv Television portal Power Stability

: Ensure the decoder remains powered on throughout the entire process to avoid permanent software damage. Step-by-Step Update Process Prepare the USB

: Copy the unzipped firmware file directly to the root directory of your USB drive (do not put it inside a folder). Connect the USB

: Insert the drive into the USB port located on the front or side of the decoder. Access the Menu : Turn on your TV and decoder. Using the remote, press the Navigate to Configuration : Use the arrow keys to find the icon (often represented by a gear or tools) and press Select Software Update : Look for an option labeled Software Update USB Upgrade Actualización por USB Start the Update I understand you’re looking for a detailed, step-by-step

Select the firmware file from the list displayed on the screen. Confirm the action by pressing

A progress bar or a blue screen message will usually appear. Wait for Reboot

: The process typically takes a few minutes. The decoder will restart automatically once finished. Do not touch any buttons until it returns to the main channel screen. Alba Ciudad 96.3 FM Troubleshooting and Maintenance File Not Found

: If the decoder doesn't see the file, ensure the USB is formatted to FAT32 and the file is in the root directory. 📌 Important notes

: For specific configuration after updating (such as re-scanning channels or adjusting satellite angles), refer to the official Newland manuals hosted on Cantv-affiliated sites. Advanced Recovery

: If the USB method fails due to a system error, advanced users sometimes use an RS232 serial cable with programs like "Ali Editor" to force a recovery update. Are you experiencing a specific error code blank screen that led you to seek an update? AI responses may include mistakes. Learn more

Important Note: The NLS3601 is an older Android SD (standard definition) decoder. Official firmware from CANTV for this model is extremely rare or no longer supported. The following steps apply to generic NLS3601 firmware updates. If this is for CANTV’s current decoders (like the Huawei or Android TV models), this procedure will not work.

Step 2: Power Off the Decoder

🔧 Step-by-step: Update CANTV NLS3601 via USB

Cómo Actualizar el Firmware del Decodificador CANTV NLS3601 por USB: Guía Definitiva (Actualización 2025-2026)

¿Tu decodificador CANTV (Modelo NLS3601) se queda congelado, reinicia en bucle, muestra error de "señal" o simplemente no abre los canales? La solución más efectiva, antes de llamar a soporte técnico, es realizar una actualización manual del firmware por USB.

En este artículo, te explicamos paso a paso cómo encontrar el archivo "new", preparar la memoria USB y flashear tu decodificador sin necesidad de internet o de un técnico especializado.

⚠️ Step 0 – Know your hardware

Open the decoder and check the PCB silk-screen (e.g., NLS3601-MB-V2.0). Firmware is not cross-compatible between revisions. Using the wrong version will brick it permanently unless you have a JTAG programmer.

2. Copy firmware file

2. Aparece "Upgrade Failed" o "Error: File mismatch"