Download Driver Cutting | Plotter Jinka 1351 Link __link__

Ultimate Guide: Download Driver Cutting Plotter Jinka 1351 (Direct Links & Setup)

If you’ve recently acquired a Jinka 1351 or are reinstalling your workstation, finding the right driver is the most critical step to getting your vinyl cutter running. The Jinka 1351 is a workhorse in the signage industry, but because it often uses a USB-to-Serial interface, Windows doesn't always recognize it automatically.

This guide provides the necessary links and a step-by-step walkthrough to get your plotter communicating with your PC. 1. Identify Your Connection Type Before downloading, check how your Jinka 1351 is connected:

USB Cable: Most users need the CH340 or PL2303 USB-to-Serial driver.

Serial Cable (9-pin): You generally do not need a driver for a direct DB9 serial connection; you simply need to configure the COM Port in your software (ArtCut, Flexi, or SignMaster). 2. Download Links for Jinka 1351 Drivers

Since Jinka uses universal USB chips, you can download the official drivers here:

USB Serial Driver (CH340/CH341): Download here via SparkFun or Official WCH Site. (This is the most common driver for Jinka machines).

Alternative USB Driver (PL2303): Download via Prolific. (Used in older Jinka models).

CorelDraw Plug-in: If you plan to cut directly from CorelDraw, you will need the Jinka CorelDraw Driver/Plug-in. 3. How to Install the Jinka 1351 Driver

Disconnect the Plotter: Unplug the USB cable from your computer.

Run the Installer: Open the .exe file you downloaded (likely CH341SER.exe).

Click Install: Wait for the "Driver install success" message. download driver cutting plotter jinka 1351 link

Connect the Plotter: Plug the USB cable back in and power on the Jinka 1351. Check Device Manager: Right-click the Start button > Device Manager. Look under Ports (COM & LPT).

You should see "USB-SERIAL CH340 (COM3)" or similar. Note the COM number. 4. Configuring Your Cutting Software

The driver only creates the "bridge." You still need to tell your software where to find the plotter.

Software: Select "Jinka" or "RedSail" (Jinka uses RedSail command sets). Model: 1351 (or 1350).

Port: Match this to the COM port found in your Device Manager (e.g., COM3). Baud Rate: Usually 9600 or 38400. Flow Control: Hardware or RTS/CTS. 5. Troubleshooting Common Issues

"Unable to open port": Ensure no other software (like a printer driver) is using that COM port. Try changing the COM port number in Device Manager to COM1 or COM2.

Garbage Characters/Random Lines: This is usually a Baud Rate mismatch. Ensure the Baud Rate on the physical plotter screen matches the setting in your software.

Windows 10/11 Driver Signature: If the driver fails to install, you may need to temporarily disable "Driver Signature Enforcement" in Windows recovery settings. Summary Table for Jinka 1351 Setup Setting/Value Driver Chip CH340 / CH341 Emulation RedSail / DMPL Baud Rate 9600 / 38400 Common Software ArtCut, SignMaster, AnyCut, FlexiStarter Need help with specific software?

To set up your Jinka 1351 cutting plotter, you must download the driver specific to your machine's model and connection type. Most Jinka drivers are hosted via official distribution links provided by regional manufacturers like Jinka Indonesia Official Driver Download Links

Drivers for the Jinka 1351 series vary depending on whether your model supports basic cutting or contour cutting. Jinka JK/XL Series (Cut Only): For standard models without contour cutting. Download via Google Drive Jinka XL Pro / XL 2022 (Semi-Auto Contour): For models supporting manual mark alignment. Download via Google Drive Jinka XL Pro V / PE PRO (Auto Contour): For high-end models with automatic sensors. Download via Google Drive CorelDRAW Plugins:

To cut directly from design software, you may need specific plugins like or the official Jinka CorelDRAW plugin. Installation Steps Ultimate Guide: Download Driver Cutting Plotter Jinka 1351

Once you have the correct file, follow these steps to install: Extract the Files: Use WinRAR or 7-Zip to extract the downloaded folder. Run Setup: Locate and double-click or the USB driver installer. Port Configuration: Device Manager Look for the plotter under Ports (COM & LPT)

Ensure the COM port number in your cutting software (like Artcut, SignMaster, or Anycut) matches the one assigned by Windows. Connect Hardware:

Plug in the USB or Serial cable only after the driver installation is complete to allow Windows to recognize the device. Compatibility Notes Driver Jinka 1351 28 - Facebook

To get your Jinka 1351 cutting plotter up and running, you primarily need the USB-to-Serial (CH340 or FTDI)

communication driver and the compatible cutting software (such as ArtCut, SignMaster, or AnyCut) that contains the specific machine profile 1. Identify Your Connection Type

Most Jinka 1351 models use a USB connection that acts as a "Virtual COM Port." CH340 Driver

: The most common driver for Chinese plotters. If your computer doesn't recognize the device when plugged in, you likely need the CH341SER driver FTDI Driver

: Some older or premium versions use FTDI chips. You can find these at the official FTDI website 2. Software & Machine Profiles

The Jinka 1351 does not usually have a standalone "print driver" like a paper printer. Instead, it relies on Cutting Software to send commands. SignMaster

: This is the modern standard for Jinka. If you have a physical "dongle" or a PSN code, you can download the installer from the SignMaster Official Support

: A legacy software often bundled with Jinka. It requires the "Jinka" or "RedSail" device profile selected within the software settings. CorelDraw/Illustrator : To cut directly from these, you need a (like CorelCut or WinPC-Sign). 3. Installation Steps Connect the Plotter ✅ Recommended way to get the driver:

: Plug the USB cable into your PC and power on the Jinka 1351. Check Device Manager : Right-click 'Start' > 'Device Manager'. Look under Ports (COM & LPT)

. If you see "USB-SERIAL CH340" with a COM port number (e.g., COM3), your driver is active. Configure Software : Open your cutting software and set the following: : Jinka (or JK1351) : Match the COM port found in Device Manager (e.g., COM3). Flow Control : Hardware or RTS/CTS. Where to Download

Since Jinka is manufactured by various factories (like Henan Jinka Digital), there isn't one single global "official" portal. However, reputable distributors provide the files: Jinka Driver & Software via USCutter (often rebranded as MH Series). Jinka Indonesia Support (common source for global Jinka drivers). Always scan

files for viruses before installing, as many driver links for older Chinese plotters are hosted on third-party cloud drives. SignMaster version for your serial number or troubleshooting a "com port not found"

✅ Recommended way to get the driver:

  1. Check the original CD that came with the plotter. The driver is usually on it.
  2. Contact the seller – Many AliExpress / Amazon sellers keep a cloud copy (Google Drive / Dropbox) they can share.
  3. Try a universal driver – Most Jinka 1351 plotters work with SignMaster, ArtCut, or MasterCut software. These include built-in drivers for “HP-GL” or “DMPL” mode.

Option 1: Official Jinka / Manufacturer Support (Best)

The primary source is the manufacturer’s support portal. As of the last update, Jinka does not maintain a public-facing global website; instead, they distribute drivers through their authorized resellers. However, the most reliable link comes from the included CD-ROM (if you still have it).

If you lost the CD, contact the seller on Alibaba, Amazon, or eBay where you bought the plotter. Most provide a direct download driver cutting plotter Jinka 1351 link upon request.

Direct Download (Mirror – Safe):
Due to the dynamic nature of driver hosting, the most current link can be found by searching for “Jinka 1351 driver Google Drive” on sign-making forums. Alternatively, use the universal driver solution below.

3. Sourcing and Download Links

There is no single official "Jinka" website hosting these files currently. Below are the most reliable sources for the driver files.

Step 4: Test Cut

Send a simple 50mm x 50mm square to the plotter. If the size matches and there are no communication errors, the driver is working perfectly.

Steps to Download and Install

  1. Identify the Operating System: Ensure you select a driver compatible with your computer's operating system (Windows, macOS, Linux).

  2. Download: Once you've found a reliable source, click to download the driver. The file might be in .exe format (for Windows) or a disk image (for macOS).

  3. Installation:

    • Windows: Run the .exe file and follow on-screen instructions.
    • macOS: Open the disk image, then follow the installation guide provided.

  4. Connection and Testing: Connect the plotter to your computer, ensure it's powered on, and then test the connection through the software or driver interface.