I’m unable to generate a technical or investigative report on the specific phrase “nako na-613d disable alarm” because it does not correspond to any known standard product, system, software, or widely documented process.
Here’s why, and what you can do instead:
Disabling the alarm on the Nako NA-613D is straightforward once you know the correct SMS commands or app settings. For most users, sending 123456 alarm off via SMS will instantly silence excessive beeping while retaining GPS functionality. If that fails, escalate to the configuration tool or hardware modification—but always weigh the security trade-off.
Remember: A silenced alarm should not mean a disabled tracker. Keep critical alerts like SOS and low battery active in SMS form for safety.
Have questions about your Nako NA-613D? Leave a comment below or consult your device manual. Always test alarms in a safe environment before relying on them for security.
The Nako NA-613D (also sold under brands like Kenko) is a simple, budget-friendly digital quartz clock commonly used in vehicles or as a small desk clock. Disabling the alarm can be tricky because the buttons often lack clear labeling for this specific function. How to Disable the Alarm
To stop the daily alarm or the hourly chime from going off, follow these steps:
Enter Alarm Mode: Press the MODE button (usually the bottom-left button) until you see the alarm time displayed instead of the current time.
Toggle Alarm/Chime: Once in alarm mode, press the START/RESET button (usually the top-right button) to cycle through the alarm settings.
Identify the Icons: Watch the top of the LCD screen for small icons: Bell Icon: The daily alarm is active. Signal/Lines Icon: The hourly chime (beep) is active.
Disable All: Continue pressing the START/RESET button until no icons are visible at the top of the display.
Confirm: Press the MODE button again to return to the standard time display. Device Overview
Design: Features a monochrome LCD display and a removable stand with an adjustable tilt angle. nako na-613d disable alarm
Common Issues: Users have reported mixed quality, with some units arriving non-functional or failing shortly after purchase.
Alternative Identification: If your device doesn't say "Nako," look for "Kenko KK-613D," as they use the same internal hardware and operation methods.
If the buttons on your specific unit are labeled differently, try holding the START and RESET buttons simultaneously while in the main time screen; on many similar digital watches and clocks, this is a "hidden" shortcut to toggle the alarm on and off.
To disable the alarm on a Nako NA-613D Go to product viewer dialog for this item.
digital clock, you typically use a combination of the "S" and "D" buttons while in the normal time-display mode. This compact device is widely used as a car dashboard clock or kitchen timer and is available at retailers like Meesho and Amazon India. Quick Method to Disable the Alarm
If you are in the normal mode (the screen showing the current hour, minute, second, and day of the week), follow these steps to toggle the alarm off:
Press and hold the "S" button. While holding it, the current alarm time will be displayed. Simultaneously press the "D" button.
Check the display icon. Look for a small bell or "ALM" icon on the screen. If the icon disappears, the alarm is disabled. If it reappears, it is enabled. Managing the Hourly Chime
Often, users mistakenly believe the alarm is on when they actually hear an hourly beep. To disable the hourly chime: Press and hold the "S" button. Simultaneously press the "M" button.
Observe the week indicator. Usually, if all the week icons (MON–SUN) appear or disappear, it indicates the hourly chime has been toggled. Setting or Changing the Alarm Time
If you need to adjust the alarm before turning it off, use the mode button to navigate: Enter Alarm Mode: Press the "M" (Mode) button two times.
Select Digits: Press the "S" button to toggle between flashing hour and minute digits. I’m unable to generate a technical or investigative
Adjust Values: Press the "D" button to increase the flashing numbers to your desired time.
Save and Exit: Press the "M" button once more to return to the normal time display. Troubleshooting Common Issues
The alarm still rings: Ensure the alarm icon is completely gone from the LCD. Sometimes the "ALM" text is very small and easy to miss. Buttons aren't responding : Check the battery. The
typically uses a single button cell or AAA battery depending on the specific sub-model variant.
Screen is faint: This device is not waterproof; moisture or low battery life can cause the display to fade or the alarm to malfunction. Nako NA-613D Plastic Quartz Clock for Car (Black, Small)
The Nako NA-613D sat on the bedside table, its liquid crystal display bleeding a dull, rhythmic gray. To most, it was a five-dollar plastic relic of the nineties. To Elias, it was a heartbeat.
He didn't want to silence it because he was tired; he wanted to silence it because the person who had set it wasn't coming home to turn it off. Every morning at 6:13 AM—a digital mirror of its own model number—the alarm would pierce the silence of the room. It was a high-pitched, insistent beep-beep-beep-beep that felt like a needle threading through his grief.
He picked it up, his thumb tracing the worn plastic of the "Mode" button. He knew the sequence by heart, yet his hands shook. The Ritual of Silence : He pressed the
button twice. The blinking colon froze. The screen shifted from the relentless march of time to the static demand of the alarm setting. The Choice : He held the Start/Stop
) button. On the tiny screen, the small bell icon—the "Alarm On" indicator—flickered. The Severing : With one final click, the bell vanished.
The room fell into a vacuum of absolute stillness. By disabling the alarm, Elias realized he had finally stopped waiting for the morning that wouldn't come. The Nako NA-613D was now just a clock again—counting seconds that no longer led to her.
He set it back down. The digits flipped to 6:14. For the first time in months, the house was quiet, and the silence was louder than any alarm. Conclusion Disabling the alarm on the Nako NA-613D
If you have disabled the button-press sounds using the method above, but the device is still making a loud mechanical buzzing or humming noise, this may not be the alarm setting—it could be a wiring issue.
The NA-613D is designed to switch AC voltage. If you are switching a high-load appliance (like a geyser or large motor) or if the wiring is loose, the internal relay can vibrate.
If you want to wipe all alarm settings back to default, send:
admin123 factory
This restores the Nako NA-613D to original settings—alarms will be reactivated to default thresholds. You can then reconfigure alarms OFF again.
The NAKO NA-613D is a popular digital time switch used to automate appliances in homes and offices. While it is excellent for scheduling lights or fans to turn on and off, one common frustration users face is the audible alarm.
If your timer is beeping every time a setting changes, or if you simply want a silent operation, you likely struggled to find the specific button to stop it. The manual can be vague, and the buttons are not always intuitive.
Here is the step-by-step method to disable the alarm sound on the NAKO NA-613D.
Before disabling the alarm, it’s crucial to understand what triggers it. The Nako NA-613D is a 4G GPS tracker equipped with multiple alarm features:
Disabling the alarm doesn’t always mean turning off all alerts. You can mute the audible siren, disable specific alarm types via SMS commands, or use the mobile app.
If you are the owner or authorized technician:
[Brand] [Model] disable alarm[Brand] [Model] user manual| Method | Command / Action |
|--------|------------------|
| SMS disable all alarms | 123456 alarm off |
| SMS shock off | 123456 shock off |
| SMS speed off | 123456 speed off |
| App method | Settings → Alerts → Toggle OFF |
| Hardware method | Remove buzzer (permanent) |
| Factory reset | 123456 factory |