Pe135 Msds - Nitocote

Nitocote PE135 is a single-component, water-based protective coating and curing compound made by Fosroc. It is primarily used for the protection of concrete structures from corrosion, chemical attack, and abrasion. Key Safety & Material Properties (MSDS Summary)

According to the Safety Data Sheet, the product has the following characteristics: Physical State: Colored liquid with a slight odor. pH Value: 6.0 – 8.0. Boiling Point: >100°C. Relative Density: Approximately 1.23 – 1.28 at 20°C. Solubility: Miscible with water.

Toxicity: Non-toxic, non-flammable, and solvent-free. It is free from coal tar pitch, aromatic amines, and asbestos.

Stability: Stable under normal storage temperatures and pressure. Technical Features & Performance

Dual Function: Acts as both a curing compound (meeting ASTM C309 requirements) and a long-term protective coating. nitocote pe135 msds

Application: Can be applied to damp, "green" concrete that is only 24 hours old, saving significant labor time.

Resistance: Highly resistant to chloride and sulfate ions, as well as a wide range of groundwater chemicals.

UV Stability: Will not deteriorate or fade when exposed to strong sunlight.

Environmental Safety: Safe for use in confined spaces due to its water-based, solvent-free formula. Application Specifications Solids Content (Weight) Drying Time (20°C) 35–40 minutes Overcoating Time (20°C) 6–7 hours Full Cure 7 days @ 25°C Adhesion Strength 1.5 N/mm² Water Absorption 0.2% (BS 1881 Pt. 122) Nitocote PE135 Safety Data Sheet | PDF | Toxicity - Scribd SECTION 15: REGULATORY INFORMATION

Important Notice Regarding MSDS vs. SDS

Before providing the document, it is crucial to understand that MSDS (Material Safety Data Sheet) is an obsolete format. It has been replaced globally by the SDS (Safety Data Sheet) under the GHS (Globally Harmonized System) standards.

Manufacturers like Fosroc (the manufacturer of Nitocote PE135) have transitioned to the 16-section SDS format. Because specific chemical formulations and hazard classifications can change, you should always obtain the latest version directly from Fosroc or your local supplier.

Below is a representative Safety Data Sheet compiled based on the typical chemical composition and hazard data for Nitocote PE135 (a solvent-based epoxy coating). This document is formatted for professional use. This product is classified and labeled in accordance

SECTION 15: REGULATORY INFORMATION

• This product is classified and labeled in accordance with GHS/CLP (EU) and OSHA (US) regulations.
• Users must ensure compliance with local workplace health and safety laws.

SECTION 7: HANDLING AND STORAGE

7.1 Precautions for Safe Handling

• Avoid contact with skin and eyes. Avoid inhalation of vapour/spray.
• Use explosion-proof electrical equipment. Ensure good ventilation.
• Do not eat, drink, or smoke in areas where the product is used.

7.2 Conditions for Safe Storage

• Store in a cool, well-ventilated area away from heat and direct sunlight.
• Keep container tightly closed and upright to prevent leakage.
• Store separately from strong oxidizing agents and strong acids/alkalis.

Section 6: Accidental Release Measures

• Personal precautions: Evacuate area. Remove ignition sources. Use explosion-proof ventilation.
• Containment: Absorb inert material (sand, vermiculite). Do not flush to sewer or waterway.
• Cleanup: Collect in approved solvent-resistant containers. Dispose according to local hazardous waste regulations.

SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY

1.1 Product Identifier

• Product Name: Nitocote PE135 (Part A & Part B)
• Product Type: Two-pack epoxy coating.

1.2 Relevant Identified Uses

• Used as a protective coating for concrete and steel structures, water tanks, and pipes.

1.3 Details of the Supplier

• Manufacturer: Fosroc International Ltd.
• Address: Drayton Manor Business Park, Coleshill Road, Tamworth, B78 3XN, UK.
• Emergency Telephone: Check local Fosroc emergency contact numbers.

Section 11: Toxicological information

• Acute toxicity: Low oral/ dermal toxicity (LD50 >2000 mg/kg).
• Skin corrosion/irritation: Irritating.
• Sensitization: Can cause allergic dermatitis (epoxy and amine components).
• Carcinogenicity: Not classified (but Bisphenol A epoxy resins may contain trace impurities – see official SDS).

Sections 10–11: Stability and Toxicological Information

• Stability: Stable under normal conditions.
• Incompatibility: Strong oxidizers, acids, isocyanates.
• Hazardous decomposition: Thermal breakdown releases toxic fumes (CO, NOx).

Toxicology:

• Acute effects: Narcotic effects at high concentrations (dizziness, headache).
• Chronic effects: Prolonged skin contact may cause dermatitis. Chronic inhalation of ethylbenzene may affect kidneys and liver.
• Routes of entry: Inhalation (primary), skin absorption, ingestion.