To install and set up a OneAccess ONE100 series router, follow these physical and logical steps based on the official ONE100 Installation Manual and Telstra User Guides. 1. Pre-Installation Requirements
Environment: Place the unit on a flat surface within 2 meters of a power outlet.
Ventilation: Avoid direct sunlight and heat sources to prevent overheating. 2. Hardware Connections The rear panel contains the following ports for connection:
Power: Connect the 12V DC power adapter (typically 2.0A or 2.2A) to the power inlet.
LAN: Connect your PC or local switch to the Ethernet ports (usually starting from Port 1/0).
WAN: Connect the uplink cable (Fiber/Copper) to the designated WAN port for internet access.
Voice (FXS/BRI): For VoIP or ISDN services, connect analog phones or faxes to the FXS ports (starting from 5/0) or ISDN PBXs to the BRI ports. 3. Initial Configuration
Once powered on, the router initializes. Access the management interface using these defaults:
Connection: Plug your PC into a LAN port; it should automatically receive an IP in the 192.168.1.xxx range.
Default IP Address: 192.168.1.1 (or 192.168.1.10 for some firmware versions). Login Credentials: Username: admin Password: admin 4. Basic CLI Setup
If using a console cable (RS-232 RJ-45), use a terminal emulator (e.g., PuTTY) with settings: 9600 baud, 8 data bits, no parity, 1 stop bit. Change WAN IP: ip address
. Set Gateway: ip route 0.0.0.0 0.0.0.0 .
Save Config: Always use the save command to ensure settings persist after a reboot. 5. Troubleshooting LEDs
Power/Status: Should be solid green. A blinking or amber LED usually indicates a boot failure or a factory-default state requiring onboarding.
Link/Activity: Flashing green on Ethernet ports indicates active data traffic. oneaccess one100 installation manual oneaccess top
If you need to factory reset the device, press CTRL+Y, then CTRL+N during the boot sequence via console to trigger the reset prompt. If you'd like, let me know: Your specific model variant (e.g., ONE100E, ONE100-8V) If you are setting up VoIP/SIP trunks or just data If you have a console cable for CLI access I can provide specific commands for your configuration.
This report outlines the essential steps and technical requirements for installing the OneAccess ONE100 Series multi-service routers, based on standard installation documentation product datasheets 1. Core Installation Steps
To ensure a stable setup, follow these physical connection procedures: Safety & Placement : Install the device within
of a dedicated mains power outlet. Avoid locations with direct sunlight, high heat, or excessive dust. Power Supply
: Connect the DC input jack from the supplied power adapter to the DC 12V power input on the router before plugging into the wall. : The ONE100 typically has no physical On/Off switch ; it boots immediately upon receiving power. Network Interfaces
: Connect the Ethernet cable from your external modem or switch to the Fast Ethernet uplink port (often marked "ETHERNET" or "ETH 1/0"). LAN Connectivity : Connect local workstations to the integrated 4-port Ethernet switch Voice Connections : Connect analog devices (phones, faxes, or PABX) to the ports as required by your specific model. 2. Technical Specifications Overview
The ONE100 series serves as a versatile Integrated Access Device (IAD) with the following standard features: : 64MB RAM and 32MB Flash. Voice Capacity : Up to 4 BRI ports and 8 FXS voice ports. : Supports IPv4, IPv6, RIP v1/v2, OSPF v2, and BGP v4.
: Integrated hardware encryption accelerator for DES, 3DES, and AES. 3. Initial Configuration & Monitoring LED Indicators : Use the front panel LEDs to verify the status of Power (PWR) Ethernet (ETH/ACT) Management Console Port : Local configuration can be performed via the RS-232 RJ-45 console port
: The device is often shipped with a default configuration (e.g., adapted for Etisalat or Telstra environments) that may require WAN IP and gateway adjustments via CLI. Voice Routing
: The voice routing table must be configured to forward calls between local ports (ISDN/FXS) and the SIP trunk. for a specific task, such as configuring the WAN IP troubleshooting ISDN ports
: Ensure the device is within 2 meters of a dedicated mains power outlet. Avoid locations with direct sunlight or excessive dust. Hardware Connection
: Connect the 12V DC input jack to the router's power input. Note that these devices typically do not have a physical on/off switch; they power up upon connection. Analogue Devices : Connect faxes, phones, or PBX systems to the
interfaces on the rear panel, typically starting from port 5/0. Network (LAN) : Connect an Ethernet cable from your local switch to the Ethernet port 1/0 on the rear panel. Uplink (WAN)
: Connect the appropriate WAN cable (ADSL or Ethernet) to the designated Initial Configuration To install and set up a OneAccess ONE100
: Set the device's WAN IP address and router gateway using the Command Line Interface (CLI) to enable IP core network connectivity. Voice Routing
: Configure the voice routing table to map phone numbers to SIP accounts for call forwarding between ISDN/FXS ports and the SIP trunk. Save Settings
: Always use the save command to ensure your configuration persists after a reboot. Key Hardware Features Interfaces
: Integrated ADSL2/2+ modem, a 4-port 10/100 Ethernet switch, and varying combinations of 2 or 4 BRI (ISDN) ports. Voice Support
: Supports up to 8 FXS ports via optional daughter-boards for analog terminal connections.
, which provides advanced firewall, VPN features, and Quality of Service (QoS) for prioritising voice traffic.
: Includes stateful packet inspection and policy-based routing to secure the company LAN while managing public hotspots. BS Broadcast Management & Tools
: Standard industry Command Line Interface for rapid integration with automated configuration tools. Web Interface
: A web-based configurator is available for simplified LAN and WLAN setup. Maintenance
: Supports SNMP (v1/v2c/v3) and includes voice quality audit functions for monitoring jitter and echo. Detailed PDF guides are available through resources like Scribd's One100 Design & Installation Guide Telstra's IAD User Guide for the WAN interface or help troubleshooting the voice routing table? OneAccess One100E Installation Guide | PDF - Scribd
The OneAccess ONE100 is a multiservice access router designed for small to medium-sized businesses, combining high-speed data, VoIP gateway functions, and security in a single device. Core Hardware Features
Connectivity: Features include a 4-port Fast Ethernet switch, one Fast Ethernet uplink, and options for ADSL2+, BRI (ISDN), and FXS/FXO analog voice ports.
Security: Includes a stateful inspection firewall and IPsec encryption acceleration (DES, 3DES, AES) for secure VPN connections.
Software: Operates on OneOS, which supports advanced routing protocols (BGP, OSPF), Quality of Service (QoS), and extensive management via CLI or Web GUI. Physical Installation Steps Part 7: Frequently Asked Questions (FAQ) Q1: What
Preparation: Unclip the lower part of the front panel and remove the cover if you need to install internal components like the WLAN antenna.
Voice Connections: Connect analog appliances (phones, faxes) to the FXS ports on the rear panel.
Data Connections: Connect an Ethernet cable from your local switch or PC to one of the LAN/SWITCH ports.
Uplink: Connect the WAN or ADSL line to the designated Uplink or ADSL port as per your service type.
Power Up: Connect the 12V DC power adapter to the router. There is typically no On/Off switch; the device boots immediately upon being plugged in.
STATUS LED: Blinks during self-test and turns steady green after roughly 30 seconds if successful. Initial Configuration
Web GUI Access: Connect a PC to a LAN port. The PC should receive an IP in the 192.168.1.x range. Access the interface at http://192.168.1.1. Default Credentials: Username: admin | Password: admin.
CLI Setup: Use the Console port for manual configuration. Common initial commands include setting the WAN IP and configuring the default gateway.
Voice Routing: For VoIP setups, the voice routing table must be configured to map internal phone numbers to SIP trunks for inbound and outbound calls. Important Safety & Troubleshooting OneAccess - One100 - Design & Installation Guide - Scribd
Q1: What is the difference between One100 and OneAccess Top?
A: One100 is the hardware model. “OneAccess Top” is an operational term meaning full administrative privileges (level 15). You need Top access to install or reconfigure the One100.
Q2: Can I use the One100 without a console cable?
A: Yes, if the previous configuration has SSH or HTTP enabled. However, for first-time installation, the oneaccess one100 installation manual strongly recommends console access.
Q3: Does the One100 support PoE (Power over Ethernet)?
A: No. The One100 requires the included 12V DC adapter. PoE injectors for uplink are not supported.
Q4: Where can I download the official PDF of the OneAccess One100 installation manual?
A: Register at the OneAccess support portal (now part of Alec, Inc.). Search for “One100 Hardware Installation Guide” – the OneAccess Top chapter is on pages 34-47.
Historically, you would console into the One100 and type CLI commands all day. With OneAccess TOP (Telecom Operating Platform or Topology Manager), you don't.
TOP is the zero-touch provisioning (ZTP) brain. The One100 is designed to call home to the TOP server the second it gets an IP address.