Satlink Ws-6979 Software Upgrade ❲Top 10 UPDATED❳

Upgrading the software on your Satlink WS-6979 is a straightforward process handled via the device's USB port. This handheld combo meter supports DVB-S/S2/T/T2/C and MPEG-4 H.265 (8-bit) decoding. Preparation Checklist

Battery Check: Ensure your device has at least 50% battery life or is connected to the power adapter. A power failure during an upgrade can "brick" the device.

USB Drive: Use a high-quality USB flash drive (FAT32 format is recommended for compatibility).

Software Source: Only use firmware files obtained directly from authorized Satlink distributors or the official manufacturer to avoid damaging the hardware. Step-by-Step Upgrade Guide

Download Firmware: Obtain the latest firmware file (typically a .ssu or .bin file) and save it to the root directory of your USB drive (do not put it in a folder).

Connect Hardware: Plug the USB drive into the USB port on the side of the device. Navigate to Upgrade Menu: Power on the device. Press MENU on the keypad to reach the main interface.

Use the arrow keys to navigate to System or Tools (the naming varies slightly by version). Select Software Upgrade (or USB Upgrade) and press OK. Execute the Update: Select the update file from the list shown on the screen. Confirm the prompt to start the upgrade. Satlink Ws-6979 Software Upgrade

Wait: A progress bar will appear. Do not touch any buttons or power off the device until it finishes.

Final Step (Factory Reset): Once the update is complete, the device will usually reboot. It is highly recommended to perform a Factory Reset (System -> Factory Setting) after any firmware change to ensure all new settings are applied correctly. Troubleshooting Tips

File Not Found: If the device doesn't see your file, ensure the USB drive is formatted as FAT32 and not NTFS or exFAT.

Corrupted Display: If the screen stays black after a reboot, you may have used the wrong firmware version (e.g., trying to use 6980 firmware on a 6979). Contact the seller for recovery instructions.

Satlink WS-6979SE Digital Satellite Finder Meter User Manual

The Satlink WS-6979 Go to product viewer dialog for this item. Upgrading the software on your Satlink WS-6979 is

supports software upgrades directly via its USB 2.0 port. This handheld combo meter uses a Novatek microprocessor and supports file management systems like FAT32 and NTFS, which are typically required for the device to recognize update files on a flash drive. Upgrade Requirements Storage Device: A USB flash drive formatted to FAT32.

Firmware File: A valid .bin or .img update file specifically for the WS-6979 model.

Power: Ensure the 7.4V/3000mAh battery is fully charged or the unit is connected to the DC 12V/1.5A power adapter to prevent power loss during the flash process. Standard Upgrade Procedure

Prepare the USB: Download the latest firmware from a verified provider and save the file to the root directory of your USB drive.

Connect: Insert the USB drive into the Data Service Port (USB) on the side of the meter.

Navigate Menu: Power on the device and enter the System Setup or Tools menu using the 4.3-inch TFT LCD interface. Estimated Effort & Resources

Select Upgrade: Choose the Software Upgrade (sometimes labeled "USB Upgrade") option.

Start Flash: Select the firmware file from the USB list. The device will typically display a progress bar. Do not turn off the device until it restarts automatically, as this can brick the unit. Troubleshooting & Technical Notes Port Compatibility: The

features a standard USB 2.0 interface; if the drive is not recognized, try a smaller capacity drive (e.g., 8GB or 16GB) formatted specifically to FAT32.

Factory Reset: It is often recommended to perform a factory reset after a successful upgrade to ensure all new system parameters are applied correctly.

Verification: Check the "Version" or "System Info" section in the menu after rebooting to confirm the new software version is active. Satlink WS-6979

Satlink WS-6979 Satellite & Terrestrial TV Signal Meter - Sciteq

Disclaimer: Firmware upgrading carries a risk of bricking the device if done incorrectly or if power is lost. Ensure you have a stable power source. This guide is for informational purposes. Always confirm the correct firmware version with your supplier.

Estimated Effort & Resources

5. Upgrade Procedure (Step-by-Step)

2. Prerequisites & Tools

Step 2: Prepare the SD Card

  1. Insert the microSD card into your PC.
  2. Right-click the drive → Format.
  3. File system: FAT32 (not exFAT or NTFS).
  4. Allocation unit size: Default.
  5. Copy the firmware file (e.g., WS6979_V2.0_2024.abs) directly to the root of the SD card (not inside any folder).

Phase 3: Flashing Process

  1. Enter Download Mode: Power off the meter. Hold the specific boot key combination (often holding the 'OK' or '0' button while powering on, or simply connecting via USB depending on the PCB revision) until the PC software recognizes the device.
  2. File Selection: Within the Upgrade Tool, the specific firmware file (.bin) was selected.
  3. Transfer: The "Upgrade" or "Download" button was pressed.
    • Status: The progress bar moved from 0% to 100%.
    • Duration: The process took approximately 2–4 minutes.
  4. Completion: Once the prompt "Upgrade Success" or "End" appeared, the device automatically rebooted.

Step 3: The Upgrade Process

  1. Power off your Satlink WS-6979 completely.
  2. Insert the microSD card into the slot on the side of the meter.
  3. Press and hold the "POWER" button while simultaneously pressing the "MENU" button.
    • Alternate method for some units: Hold "EXIT" + "POWER".
    • Keep both buttons held until the screen lights up with an “Upgrade” or “Bootloader” message.
  4. The device will automatically detect the firmware file and ask: “Upgrade Firmware? Yes/No”.
  5. Press "OK" (or the right soft key) to confirm.