Skip to content

Sp Flash Tool Stuck On ((link)) Download Da 100 〈EXCLUSIVE〉

SP Flash Tool hanging at "Download DA 100%" indicates a failure to establish a handshake after successfully loading the Download Agent, usually caused by driver conflicts, hardware issues, or Secure Boot restrictions. Key solutions include reinstalling MediaTek VCOM drivers, using a device-specific custom DA file, switching to USB 2.0 ports, and verifying the phone is powered off during connection. For more detailed solutions, visit Hovatek.

List of sp flash tool error codes, meanings & how to fix (solution)

2. Use the Correct Download Agent (DA) File

Different chipsets require specific DA versions.

  • Try a different DA file: In SP Flash Tool, go to Options → Download Agent → select a different .bin file (e.g., MTK_AllInOne_DA.bin or a custom DA for your chipset).
  • For newer chips (Helio G-series, Dimensity), use the DA file extracted from the stock ROM of that device.

Primary Causes of "Download DA 100%" Error

| Cause Category | Specific Issue | |----------------|----------------| | Driver Issues | Wrong USB VCOM driver, driver signature disabled, or driver conflict. | | USB Problems | Bad cable, USB 3.0 port, loose connection, or power fluctuation. | | Storage Failure | Corrupted eMMC, damaged partitions (especially NVRAM or bootloader). | | Bootloader State | Bootloader is locked or partially bricked (BROM mode disabled). | | Version Mismatch | Using an outdated DA or SP Flash Tool version for your chipset. | | Battery/Voltage | Dead battery, battery too low, or phone refusing to stay in BROM mode. |

Prevention and safety notes

  • Always backup user data before flashing. Flashing can wipe data or permanently brick the device.
  • Use firmware and DA files matching the exact model and SoC revision.
  • Avoid “Format All + Download” unless instructed by a reliable guide.
  • If device uses secure boot, unlocking or flashing unofficial firmware may be blocked and could void warranty.

Writing a Useful Feature to Handle Such Situations:

If you're looking to create a tool or script to automate these steps or provide more feedback during the flashing process, here are some ideas:

  • Auto-USB-Checker: A feature that automatically checks and reports USB connectivity issues.
  • Driver Auto-Updater: Automatically updates the device drivers to the latest version.
  • Firmware Checker: A built-in feature that checks if the firmware is compatible with the device.
  • Status Monitor: A feature that provides detailed status updates during the flashing process, helping to identify where it gets stuck.

Implementing such features could significantly enhance the usability of SP Flash Tool or similar software, providing a more robust and user-friendly experience for fixing common issues like getting stuck on "Download DA 100%".

SP Flash Tool Stuck on "Download DA 100%" - A Troubleshooting Guide

If your SP Flash Tool is stuck on "Download DA 100%" while trying to flash your device, don't worry, this guide will help you troubleshoot and possibly fix the issue.

To disable Fast Boot:

  1. Control Panel → Power Options → "Choose what the power buttons do".
  2. Click "Change settings that are currently unavailable".
  3. Uncheck "Turn on fast startup (recommended)".
  4. Restart your PC.

Also, go to Device Manager → Universal Serial Bus controllers → Right-click each USB Root Hub → Properties → Power Management → Uncheck "Allow the computer to turn off this device".

Introduction: The Frustration of a Frozen Flash

You’ve set up SP Flash Tool, loaded the correct scatter file for your MediaTek (MTK) Android device, and clicked "Download." The red bar fills up slowly, then the purple bar, and finally, the yellow bar reaches 100%. But then it happens: "Download DA 100%" appears in the status log, and the process stops. No error message. No progress. Just a frozen tool and a bricked phone.

This is one of the most common and frustrating errors in the Android flashing community. The "DA" in "Download DA" stands for Download Agent—a small piece of firmware that SP Flash Tool sends to the phone’s RAM to manage the flashing process. When the tool gets stuck at 100% of this step, it means the DA was sent successfully, but the phone failed to execute it or handshake with the PC.

In this article, we’ll dissect exactly why this happens and provide 12 actionable solutions, ranked from most likely to most advanced.

6. Try a Different Version of SP Flash Tool

  • v5.x – Best for older MT65xx/MT67xx chips.
  • v5.20xx+ – For MT67xx, MT68xx.
  • v5.21xx+ – For Helio P/G series.
  • v5.24xx+ – For Dimensity chips.

Use the version recommended by your ROM provider – mixing old tool with new chip often causes DA hang.

Precautions:

  • Always backup your device data before attempting to flash it.
  • Be cautious when using flashing tools, as incorrect usage can brick your device.

By following these steps, you should be able to resolve the issue of the SP Flash Tool being stuck on "Download DA 100%". If the problem persists, consider seeking help from device-specific forums or support channels.

When using the SP Flash Tool, seeing the yellow progress bar reach Download DA 100%

and then stop is a frustrating but common bottleneck. This state usually signifies that the "Download Agent" (DA)—the small piece of software that communicates with your device's internal storage—has successfully loaded into the phone's SRAM, but the tool is failing to transition to the actual firmware flashing stage. Stack Overflow Why the Tool Gets Stuck at 100% sp flash tool stuck on download da 100

The "Download DA 100%" freeze is rarely a software "crash" and more often a communication or compatibility breakdown . Key reasons include: Secure Boot Conflict

: Many modern MediaTek devices (like those from Xiaomi or Oppo) have a secure bootloader that requires a specific "Secure DA" file to authorize the flashing process. Driver Handover Failure

: The PC might successfully send the DA file but fail to switch to the MediaTek VCOM driver required for the subsequent data transfer. Hardware Interruption

: Issues like a faulty USB cable, a loose port, or insufficient battery power can cause the target device to shut down unexpectedly right after the DA is received. Step-by-Step Solutions 1. Use a Secure Download Agent (DA) If your device has a secure bootloader, the default MTK_AllInOne_DA.bin might not work. Locate the specific DA : Look for a file named DA_SWSEC.bin

or a DA file specifically provided with your phone's stock firmware. Select it in the tool : In the SP Flash Tool interface, click the button next to Download-Agent and select the specialized 2. Re-install or Force VCOM Drivers

The jump from 100% DA to the actual download requires a stable VCOM connection. Manual Install Device Manager

, right-click your computer name, and select "Add legacy hardware" to manually install MediaTek Preloader USB VCOM Port Check

: Ensure you are using a direct USB port on your motherboard (back of the PC) rather than a USB hub or front-panel port, which may lack sufficient power. 3. Hardware Interaction (Key Combos)

Sometimes the device needs a physical "nudge" to enter the correct state after the DA is sent. The Volume Trick : Try holding Volume Down

(or sometimes Volume Up, or both) while connecting the USB cable. Do not release them until the progress bar moves past the yellow DA stage. Power Reset

: If the phone has a removable battery, take it out and put it back in before starting. Ensure the phone is completely switched off before connecting. 4. Tool & File Configuration

SP Flash Tool 2025 Free Download Latest Version for Windows and Linux

Getting stuck at "Download DA 100%" in SP Flash Tool is a common bottleneck that indicates the software has successfully sent the Download Agent (DA) to your device's internal RAM but is now failing to establish a handshake to proceed with the actual firmware flashing. Understanding the "Download DA 100%" Hang

The Download Agent is the critical intermediary software that allows your PC to communicate with the MediaTek (MTK) chipset. When it reaches 100% and halts, it usually means the device has "accepted" the agent but cannot initialize the next phase—often due to driver conflicts, security boot protocols, or hardware connection drops. Proven Solutions to Resolve the Freeze 1. Update or Reinstall VCOM Drivers

The most frequent cause is an unstable or incorrect MediaTek Preloader VCOM driver. SP Flash Tool hanging at "Download DA 100%"

Clean Slate: Use a tool like USBDeview to uninstall all existing MTK and VCOM drivers.

Manual Install: Restart your PC and manually install the VCOM drivers through the Device Manager via "Add Legacy Hardware". 2. Swap the Download Agent (DA) File

Modern MTK devices, especially those with Secure Boot, often require a specific DA file rather than the default MTK_AllInOne_DA.bin. Navigate to the Download-Agent field in SP Flash Tool.

Select a DA file specifically provided with your phone’s stock firmware or try a Secure Boot DA. 3. Adjust Connection Settings and Physical Hardware

The tool may be timing out because it loses contact with the device immediately after the DA is loaded.

USB Speed: Go to Options > Option > Connection and set the USB Speed to Full Speed instead of High Speed.

Physical Connection: Try a different USB cable (preferably the original) and a USB 2.0 port on your PC; USB 3.0 ports often cause communication drops with flashing tools.

Battery State: Ensure the battery is at least 50% charged and firmly inserted. Some devices require holding a volume button (usually Volume Down or both) while connecting to stay in the correct mode.

List of sp flash tool error codes, meanings & how to fix (solution)

The SP Flash Tool getting stuck at "Download DA 100%" (often shown as a red bar) usually means the tool has sent the initial boot instructions but cannot establish a stable data connection to start the actual flashing process. Common Fixes for the "Download DA 100%" Hang

If the progress bar fills to 100% and then hangs without moving to the next stage (yellow bar), try these troubleshooting steps:

Try Different Key Combinations: When connecting the USB cable, try holding different buttons. Common combinations include Volume Up, Volume Down, or both simultaneously.

Switch USB Ports and Cables: A common culprit is a faulty cable or a port that doesn't provide enough power. Use a high-quality data cable and try the USB ports on the back of your PC (if using a desktop).

Update or Reinstall VCOM Drivers: Ensure you have the correct MediaTek (MTK) VCOM drivers installed. If they are corrupted, uninstall them using a tool like USBDeview and reinstall the latest version.

Run as Administrator: Right-click flash_tool.exe, go to Properties > Compatibility, set it to Windows XP (Service Pack 3), and check Run this program as an administrator. Try a different DA file: In SP Flash

Use the Latest Version: Sometimes the "Download DA 100%" error is caused by a version of the tool that doesn't support your specific chipset. Download the latest version of SP Flash Tool or one specifically recommended for your device.

Check the Download Agent (DA): Ensure you are using the correct MTK_AllInOne_DA.bin file or a specific DA file provided with your device's firmware. Quick Safety Tip

Always untick the Preloader box unless you are absolutely sure you need to flash it, as flashing an incorrect preloader can permanently "brick" (disable) your device.

When SP Flash Tool gets stuck at Download DA 100% (often represented by a solid red bar), it means the tool has successfully loaded the Download Agent (DA) into the device's internal SRAM but is failing to initiate communication with the phone's DRAM or external memory. Common Fixes for the 100% Hang

Toggle Boot Keys: While the tool is stuck at 100%, try holding different button combinations on your device (e.g., Volume Up, Volume Down, or both) while it's connected.

Driver Reset: Conflicting drivers can stall the process. Use a tool like USBDeview to uninstall old VCOM and Preloader drivers, then reinstall the latest MediaTek USB VCOM drivers.

Try Different Tool Versions: Older MediaTek chips (like MT6575/MT6577) often require specific older versions of SP Flash Tool, while newer chips need the latest v5 or v6 releases.

Run as Administrator: Right-click flash_tool.exe and select Run as Administrator. You might also need to set the Compatibility Mode to Windows XP Service Pack 3 for older versions. Check Hardware Connections:

Switch to a different USB port (preferably one directly on the motherboard if using a desktop).

Ensure the battery is inside and sufficiently charged, or try the process without the battery if your device supports it.

File Selection: Ensure you are using the correct DA_SWSEC.bin or MTK_AllInOne_DA.bin file provided with the firmware or the tool. Common Error Meanings

List of sp flash tool error codes, meanings & how to fix (solution)

This is a very common issue when flashing MediaTek (MTK) devices. It usually means the SP Flash Tool is waiting for a response from the phone’s preloader, but the connection is being blocked, interrupted, or misunderstood by the computer.

Here is a step-by-step troubleshooting guide to fix "Stuck on Download DA 100%".