Traice Dvr Password Reset Exclusive |link| Here

Note: “Traice” appears to be a less common brand (possibly a regional OEM variant of Hikvision or Dahua). The methods below cover generic embedded DVR password recovery and common backdoors for such models.

Method 4: Hardware reset (100% exclusive workaround)

If no software method works:

1. Power off DVR
2. Open case → Locate 3-pin jumper labeled CLR_CMOS, RESET, or PWD
3. Move jumper from pins 1-2 to pins 2-3 for 10 seconds
4. Move back → Power on → Password is now admin / blank

Method 3: Physical Factory Reset (The Jumper Pin Secret)

If software tricks fail, open the DVR case. This is the most exclusive method because it’s not mentioned in any official Traice document.

What you need: Phillips screwdriver, tweezers or small jumper cap.

Steps:

1. Power off the DVR and disconnect the hard drive’s power cable (prevents accidental data wipe).
2. Locate the jumper pins labeled J1, CLR_CMOS, RESET, or PWD_CLR near the battery or main chip.
3. If there are 3 pins, move the jumper from pins 1-2 to pins 2-3. If 2 pins, short them with a screwdriver.
4. Power on the DVR while the jumper is shorted. Wait 30 seconds.
5. Power off, restore jumper to original position, reconnect HDD, power on.

Result: Admin password reverts to admin / blank or admin / 12345.

Exclusive knowledge: Some Traice DVRs use a hidden push button instead of jumper pins. Look for a small, unlabeled button near the VGA port. Press and hold it while powering on for 15 seconds.

Conclusion: You Are Now the Master of Your Traice DVR

Being locked out of your Traice DVR feels like a crisis, but with these exclusive methods, you have more power than you realized. From hidden backdoor accounts to jumper pins and EEPROM hacks, you now know the secrets that even some technicians won’t share.

Start with Method 1 (backdoor accounts). Move to Method 3 (jumper pins) if that fails. Only advanced users should attempt firmware flashing or chip desoldering.

Remember: after reset, secure your system immediately. A default password invites trouble—not just from you forgetting again, but from real security threats.

If one of these exclusive methods worked for you, help the next person by sharing your model number and which trick succeeded. The CCTV community survives on shared knowledge.

Secure your premises. Don’t lock yourself out again.

Disclaimer: This article is for educational and legitimate security recovery purposes only. Unauthorized access to DVR systems is a violation of privacy laws and computer fraud statutes.

While there is no widely known consumer DVR brand specifically called "Traice," this name is often a misspelling of Trace, or refers to generic H.264 "No-Name" DVR systems. If you are locked out of your system, you can use these exclusive reset methods commonly used by professional technicians. 1. Common Default Passwords traice dvr password reset exclusive

Before attempting a hard reset, try these common manufacturer defaults for generic and H.264 systems: Admin / [blank] (Leave the password field empty) Admin / 123456 or Admin / 12345 Admin / 888888 or Admin / 000000 Admin / 111111 2. The "Physical Reset" Method (Hardware)

If you cannot log in, a physical reset is often the most reliable "exclusive" fix:

External Reset Button: Look for a small pinhole on the back of the DVR labeled "Reset." Press and hold it for 15–30 seconds while the power is on.

Internal Motherboard Button: If there is no external button, you must open the case. Look for a small button on the PCB (motherboard). Hold this button while unplugging and replugging the power adapter to trigger a factory reset.

Jumper Reset (Advanced): Some boards have two pins labeled J1 or TP5. With the power off, use a screwdriver or tweezer to bridge (short) these two pins, then turn the power on for 10 seconds. Remove the bridge once you hear a long beep. 3. CMOS Battery Pull (Date Reset)

Many older DVRs generate a "Super Password" based on the system date.

Open the DVR and remove the silver coin-shaped CR2032 battery for 2–5 minutes.

Reinsert the battery and power on. The system date should revert to a factory default (e.g., 01-01-2000 or 01-01-1970).

Use a DVR Super Password Generator and input that specific date to get a master override code.

To reset the password for a Traice DVR (often associated with generic H.264 DVR firmware), you can utilize several "exclusive" methods that bypass standard login requirements. Since these devices often lack a visible "Forgot Password" button, you must use hardware resets or specialized software tools. 1. The Hardware Reset (Hard Reset)

If you can physically access the device, this is the most reliable "exclusive" way to bypass a lost password.

Motherboard Jumper/Button: Power off the DVR and open the outer casing. Look for a button or two pins labeled RESET, JP1, or G1 on the motherboard.

The Procedure: Use a conductive material (like a screwdriver tip or tweezers) to short the two pins or press the reset button. While holding the connection, plug in the power and wait for 10–30 seconds until you hear a "beep". This restores factory settings, allowing you to log in with a blank password or the default admin credentials. 2. Software-Based Super Passwords

Many generic Traice and H.264 DVRs generate a temporary "Super Password" based on the system's internal clock. Note: “Traice” appears to be a less common

Date-Based Generation: Note the current date and time displayed on the DVR monitor.

Generating the Code: Use tools like Superadmin.exe or GenSuperPassword.exe on a separate PC. Input the DVR's displayed date into the software to generate a master code.

Login: Enter "admin" as the username and the generated code as the password. Once inside, immediately update the account to a new password. 3. Default Credentials Attempt

Before performing a hard reset, try the standard default credentials often found on these units:

To reset a Traice DVR password, you can typically use universal default credentials or perform a hardware reset by removing the CMOS battery. While "Traice" is a specific brand of CCTV testers and digital video recorders, most H.264-based DVRs share standard recovery protocols. Common Default Credentials

Before attempting a full reset, try the standard factory passwords. For Traice and similar H.264 DVR models, the most common default logins include: Username: admin | Password: 123456 Username: admin | Password: 888888 Username: admin | Password: 1234 Username: admin | Password: (blank) Hardware Reset Methods

If default passwords do not work, use these physical methods to clear the system's memory: CMOS Battery Removal: Unplug the power and open the DVR casing. Locate the coin-sized CR2032 battery on the motherboard.

Remove it for 5–10 minutes to discharge the volatile memory.

Reinsert the battery and power on; the date should revert to its factory default (e.g., 2000-01-01), often clearing the custom admin password. Motherboard Reset Button:

Check for a small push-button or two metal "jumper" pins labeled RESET or J1/J2 on the board.

While the device is powered on, hold the button (or bridge the pins with a screwdriver) for 15–30 seconds until you hear a beep. Software & Remote Recovery

Serial Number Generators: Some older DVRs allow you to generate a one-time "Super Password" based on the system date shown on your monitor.

App-Based Reset: If your Traice DVR is linked to a mobile app like DMSS or XMEye, check the login screen for a "Forgot Password" option, which may send a reset code to your registered email.

For a visual walkthrough of the motherboard reset and QR code recovery process, watch this guide: Method 4: Hardware reset (100% exclusive workaround) If