The Tecom TS1162 is a 3-LED Remote Arming Station (RAS) designed for the Challenger security system. It is frequently used in demanding environments due to its robust construction and IP67 rating, making it suitable for dusty or wet locations. 🛠️ Core Installation Steps
Installation typically involves mounting the unit and connecting it to the Challenger RS-485 LAN.
Preparation: Ensure all power to the Challenger panel is off before beginning any wiring. Mounting:
Separate the body from the base by removing the retaining screws at the bottom.
Use the base as a template to mark mounting holes on a flat, vertical surface.
Secure the base using suitable screws, ensuring the tamper lever is properly depressed against the mounting surface. Wiring and Addressing:
LAN Connection: Connect the unit to the RS-485 LAN (up to 1.5 km from the panel).
DIP Switch Configuration: Set the unique RAS address using DIP switches 1 through 4.
Termination: If this is the last device on the LAN, set the LAN termination (DIP switch 8) to ON.
Final Assembly: Hook the top of the body onto the base tabs, swing it down, and replace the retaining screws. 📋 Key Features & Specifications
Outputs/Inputs: Includes one request-to-exit (RTE) input and one open collector output for controlling door relays or strikes.
Protection: Rated IP67 for superior weather and dust resistance.
Connectivity: Directly compatible with Challenger RS-485 LAN. Indications: Features 3 LEDs to display area status. 🔒 Accessing Official Manuals
Official technical documentation for Tecom hardware is often restricted to trained installers.
Aritech Support: You can request full installation and programming manuals via the Aritech Support Portal using professional credentials.
Replacement Parts: Items like the TS1162 Stick-on Membrane Label are available through specialized security retailers.
If you tell me what specific installation environment you're working with: Outdoor or High-dust area setup Door strike or Request-to-Exit wiring Troubleshooting a specific LED or LAN error I can provide more tailored technical advice. Remote Arming Station (RAS) Keypad, 3 LED - Aritech Remote Arming Station (RAS) Keypad, 3 LED - Aritech. aritech.com.au Tecom Manuals - Kidde Global Solutions Support
Exclusive Installation Guide for the Tecom TS1162 3-LED RAS Keypad
The Tecom TS1162 3-LED Remote Arming Station (RAS) is a specialized access control and security keypad designed for durability in demanding environments. This guide provides an exclusive, detailed walkthrough for installing and configuring the Tecom TS1162 within a Challenger security system. Key Specifications and Features
Before beginning the installation, ensure you are familiar with the device’s capabilities as outlined in the Aritech TS1162 Datasheet. ts1162 installation manual exclusive
IP67 Rating: Fully protected against dust and immersion in water, making it suitable for wet or outdoor environments.
Connectivity: Connects via the Challenger RS-485 LAN, supporting distances up to 1.5 km from the main controller.
Integrated Controls: Features a dedicated Request to Exit (RTE) input and an open collector output for controlling door relays or strikes.
LED Feedback: Three status LEDs provide clear system arming and area status information. Step 1: Pre-Installation Requirements
Qualified Personnel: Installation should be performed by trained security technicians. If electrical wiring for a power outlet (GPO) is required, you must use a qualified electrician.
Mounting Surface: Select a flat, solid, vertical surface. Mounting on uneven surfaces can cause the base to flex, potentially compromising the IP67 seal.
Cabling: Use high-quality twisted-pair cable for the RS-485 connection to ensure signal integrity over long distances (up to 1.5 km). Step 2: Mounting the Unit
Template and Drilling: Use the base of the TS1162 or the provided gasket as a template to mark the four mounting hole locations.
Cable Entry: Prepare the cable entry point on the mounting surface. Ensure the cable is fed through the waterproof grommet or sealant provided with the unit.
Securing the Base: Use appropriate screws or bolts for the surface material (e.g., masonry anchors for brick or self-tapping screws for metal). Tighten firmly but avoid over-tightening, which can warp the plastic housing. Step 3: Wiring and Connections
The TS1162 connects directly to the Challenger system’s LAN.
RS-485 LAN: Connect the D+, D-, +12V, and 0V terminals to the corresponding terminals on the Challenger LAN bus.
RTE Input: If using an exit button, connect it to the Request to Exit input.
Door Control: The open collector output can be wired to a door relay or strike. For high-draw strikes, ensure a separate power supply and flyback diode are used to protect the keypad circuit. Step 4: System Addressing and Programming
Once hardware is installed, the RAS must be identified by the Challenger panel.
Set the Address: Use the DIP switches or software configuration (depending on your specific panel version) to assign a unique address to the RAS.
Panel Configuration: Log in to the Challenger Installer Menu (typically Menu + Installer Code + 19) to add and configure the new station.
Testing: Verify the 3-LED status indicators correctly reflect the arming state of the assigned areas. Test the RTE input and the door strike output to ensure full functionality. Maintenance and Replacement
The TS1162 is built for longevity, but for high-traffic areas, components like the front label may wear. Genuine replacement labels are available to maintain the professional appearance and legibility of the device. Tecom 3 LED RAS replacement label - GSA Systems The Tecom TS1162 is a 3-LED Remote Arming
TS1162 Installation Manual Exclusive Report
Introduction
The TS1162 is a state-of-the-art device that requires careful installation to ensure optimal performance and safety. This report provides a comprehensive guide for the exclusive installation of the TS1162, highlighting key considerations, step-by-step procedures, and essential precautions.
Pre-Installation Requirements
Before commencing the installation, ensure that:
Installation Steps
The following steps outline the installation procedure for the TS1162:
Step 1: Unpacking and Inspection (Time: 15 minutes)
Step 2: Mounting and Placement (Time: 30 minutes)
Step 3: Electrical Connections (Time: 45 minutes)
Step 4: Configuration and Testing (Time: 60 minutes)
Safety Precautions
During installation, observe the following safety precautions:
Post-Installation Checklist
After completing the installation, verify that:
Conclusion
The exclusive installation of the TS1162 requires careful attention to detail, adherence to safety guidelines, and a comprehensive understanding of the device's specifications and requirements. By following this report, installers can ensure a successful and safe installation of the TS1162.
Appendix
Revision History
Disclaimer
The information contained in this report is provided "as is" and without warranty of any kind, either express or implied. The manufacturer assumes no responsibility for any errors or omissions in this report or for any consequences arising from its use.
Connectivity: The keypad connects directly to the Challenger RS-485 LAN.
Distance: It can be installed up to 1.5 km away from the main Challenger panel or controller.
Mounting: Suitable for both indoor and outdoor environments, featuring a robust molded plastic housing.
Environmental Protection: Rated at IP67, making it resistant to dust and water exposure. Wiring & Interface
Request to Exit (RTE): Includes a dedicated input for an egress button or RTE control.
Door Control: Features an open collector output used to drive a door relay or electric door strike.
Indicators: Utilizes 3 LEDs to provide clear status feedback for system arming and access. Quick Setup Reference
If you are integrating the TS1162 into a Tecom Challenger system, remember these standard installer defaults: Default Installer Code: 4346. Installer User Number: 50.
Management Software: Compatible with Tecom C4 and Tecom Titan for advanced configuration and multisite management.
For further programming details, refer to the ChallengerPlus Programming Manual.
Tecom Titan - Default Password & Password Reset Instructions
Before we turn a single bolt, consider the data: Over 34% of TS1162 returns are classified as "No Fault Found" (NFF) by manufacturers. In reality, these units failed due to installation errors—improper grounding, incorrect shim stacking, or thermal misalignment. This TS1162 Installation Manual Exclusive is designed to turn that 34% into 0%.
The TS1162’s sensitive Hall-effect sensors are vulnerable to ground loops. The standard manual shows a basic earth connection; this exclusive manual provides a star-point ground topology.
Most manuals tell you to run the unit at 50% speed for an hour. That is insufficient. Follow this three-phase exclusive validation:
The TS1162 is a heavy-duty time switch designed to control lighting, heating, pumps, motors, or other electrical loads. Before proceeding, please review these critical safety warnings:
When it comes to precision engineering and high-stakes equipment, the TS1162 stands in a league of its own. Whether you are integrating this component into a heavy-duty industrial conveyor, a specialized automotive rig, or a high-frequency manufacturing line, proper installation is not just recommended—it is mandatory. However, for months, technicians and engineers have searched for a resource that goes beyond the generic fold-out pamphlets. Today, we deliver that resource. Welcome to your TS1162 Installation Manual Exclusive—a deep-dive guide that covers calibration, torque sequencing, environmental tolerances, and diagnostic troubleshooting unavailable in standard documentation.
Most manuals tell you to tighten bolts in a star pattern. That is too vague. Here is the exclusive TS1162 Zero-Gap Method: Authorized Personnel : Only authorized and trained personnel
Clean the mounting port with a lint-free wipe and isopropyl alcohol. The manual states: "Even a single grain of sand can cause a 0.5% full-scale error." Apply a thin layer of thread sealant (Loctite 567, specifically) to the male threads of the TS1162. Do not use PTFE tape; it lubricates too much and will throw off your torque reading.