Usb Device Id Vid 1e3d Pid 198a Top ((free)) May 2026

The USB device with generic flash drive controller manufactured by Chipsbank Microelectronics Co., Ltd

. These identifiers typically correspond to high-speed USB 2.0 mass storage devices, often using the controller series. www.reddit.com

This guide covers identification, common issues (like "fake capacity" or "no media" errors), and repair tools. 1. Device Specifications Manufacturer (VID 1e3d): Chipsbank Microelectronics Product (PID 198a): Flash Disk / Mass Storage Device Common Controllers: CBM2199E, CBM2199S, or CBM209x series. USB 2.0 (High Speed). 2. Common Scenarios & Troubleshooting

This specific VID/PID is frequently found in budget or unbranded "no-name" flash drives, sometimes used in counterfeit devices that report fake storage capacities (e.g., a 32GB drive that only has 8GB of actual NAND memory). www.reddit.com Potential Cause Recommended Action No Media / 0 Bytes Firmware corruption or partition table error. Use a low-level format tool specific to Chipsbank. Write Protected

The controller has locked the NAND to prevent further data loss. Flash the firmware using the APTool or UMPTool. Fake Capacity Firmware is spoofing the actual storage size. Run a test with to verify real capacity. 3. Repair & Formatting Guide

If your device is malfunctioning (showing as "Unknown Device" or "No Media"), follow these steps to attempt a recovery: Extract Detailed Hardware Info: Use a tool like ChipGenius Flash Drive Information Extractor

to confirm the specific controller part number (e.g., CBM2199E). Find the Correct Production Tool: Search for the specific controller version on sites like FlashDrive-Repair.com (often listed as Chipsbank UMPTool Low-Level Format: Open the mass production tool (UMPTool). Plug in the device; it should appear in one of the slots.

Select "Start" to perform a low-level format and re-verify the memory blocks. This will permanently erase all data. 4. Verified Drivers Generally, this device uses the standard USB Mass Storage Class driver

built into Windows, macOS, and Linux. If the device isn't recognized, it is likely a hardware or firmware failure rather than a missing driver. For legacy systems (e.g., Windows 7), generic drivers are sometimes hosted on sites like DriverScape

Is your device showing a specific error message like "Please insert a disk" or "Disk is write-protected"? usb device id vid 1e3d pid 198a top

The USB device ID VID 1e3d PID 198a refers to a mass storage flash drive manufactured by Chipsbank Microelectronics Co., Ltd.. These devices are commonly budget-friendly, generic USB flash drives or "no-name" promotional sticks often used for data storage or distribution. Device Profile: Chipsbank Flash Disk Vendor: Chipsbank Microelectronics (VID 1E3D). Product ID: 198a. Controller: Typically uses the CBM2199E controller. Type: USB 2.0 Mass Storage Device.

Performance: Described as "HighSpeed" under the USB 2.0 protocol, though actual speeds depend on the specific flash memory chip paired with the Chipsbank controller. The "Chipsbank Experience": A Review

For a user, encountering this device usually means you've plugged in a generic flash drive. Based on technical databases like DeviceHunt and community reports from USBDev, here is what to expect:

Reliability: These are entry-level controllers. While functional for basic file transfers, they are frequently found in low-cost or promotional drives that may have a higher failure rate over time compared to premium brands.

Compatibility: Works natively with Windows, macOS, and Linux as a standard "USB Mass Storage Device" without needing manual driver installation.

Maintenance: If the device becomes unrecognized or shows "Write Protected," specialized tools like the Chipsbank APTool or UMPTool are often required to reflash the firmware. Troubleshooting Tips If your computer fails to recognize this device:

How do I check the PID and VID of my USB device? - Knowledge Center

The USB hardware ID VID 1e3d PID 198a identifies a generic Flash Disk manufactured by Chipsbank Microelectronics Co., Ltd

. These IDs are often associated with low-cost or "no-name" USB drives, as well as some counterfeit storage devices sold on marketplaces like AliExpress. Technical Device Breakdown Vendor (VID): — Chipsbank Microelectronics Co., Ltd. Product (PID): — Flash Disk / ChipsBnk Flash Reader. Common Controllers: Frequently uses the Chipsbank CBM2099E controller chips. USB 2.0 (High Speed). Common Issues and Identification The USB device with generic flash drive controller

This specific ID is notorious in tech support forums for appearing on drives that have "failed" or were manufactured with "fake" capacities. "No Media" Error:

Users often report that the computer recognizes the device (the "ChipsBnk" controller) but shows "No Media" or a capacity of

. This typically indicates a communication failure between the controller chip and the flash memory chip. Fake Capacity Warnings:

Some "16TB" or "2TB" SSDs/thumb drives from discount sites use this Chipsbank ID to trick the OS into reporting a high capacity, while the actual physical storage is much lower (e.g., 32GB or 64GB). Device Recognition: In Linux, it usually appears in ID 1e3d:198a Chipsbank Microelectronics Co., Ltd Flash Disk Troubleshooting and Recovery Steps

If your device is showing this ID but isn't working correctly, you can try the following: Identify Real Specs: Use tools like ChipGenius Flash Drive Information Extractor (usbflashinfo) to get the exact controller part number and Flash ID. Controller-Specific Tools:

If the drive is non-functional but detected, you may need a "Mass Production Tool" (MPTool) specific to the Chipsbank CBM2099/2199 series to re-initialize the controller. Check for Counterfeits: (Windows) or

(Linux/Mac) to test the actual storage capacity. If the test fails early, the drive's advertised capacity is likely fake. Hardware Test Mode:

For advanced users, some forum guides suggest putting the chip into "test mode" by shorting specific pins on the controller to force the computer to recognize it as a generic bootable device for firmware reflashing.

Using mass production tools or shorting pins often results in complete data loss. If you need the data, consult a professional recovery service before attempting firmware fixes. Are you trying to recover data from a drive with this ID, or are you looking for the firmware/drivers to fix a "No Media" error? USB\VID_1E3D = Chipsbank Microelectronics Co., Ltd Caution: Only do this if you know the

Step 5: Use Zadig (Advanced User)

Zadig is a tool that installs generic WinUSB or libusb drivers.

• Caution: Only do this if you know the device is for programming (Arduino, JTAG).
• Run Zadig. Select the device "VID 1E3D PID 198A" from the dropdown.
• Replace the driver with WinUSB (v6.1.7600.16385) .
• Click "Replace Driver." This makes the device visible to software like OpenOCD or CoolTerm.

Step 1: Identify the Physical Device (Critical)

Do not guess. Unplug the USB device. Does the "VID 1E3D PID 198A" disappear from Device Manager? If yes, that is your culprit.

• If it is a cable (e.g., printer or sewing machine cable): You need a USB-to-Serial driver.
• If it is a flashing box (e.g., satellite receiver programmer): You need the proprietary software for that box.
• If it is a flash drive: The controller is dead. Data recovery is required.

4. Hardware Disabled in BIOS (FIPS Mode)

Some enterprise laptops (Dell/HP) allow disabling fingerprint readers at the firmware level for security. If the device shows as "Unknown USB Device (Device Descriptor Request Failed)," the hardware may be physically turned off.

How to Extract the Infamous Driver from Windows.old

Many users find this error after a Windows reinstall. Your old driver might be sitting in the Windows.old folder.

1. Navigate to C:\Windows.old\System32\DriverStore\FileRepository.
2. Search for folders containing chiphead.inf, usbser.inf, or oem*.inf.
3. In Device Manager, update the driver > Browse my computer > Point the path to C:\Windows.old\...\FileRepository.
4. Check "Include subfolders." Install.

User Experience & Troubleshooting

• Driver Issues: Some users report conflicts after Windows updates, necessitating reinstallation of Silead's official drivers.
• Linux Users: May encounter limited gesture support unless using specific kernel modules (e.g., hid-silead for USB touchpads).
• Firmware Updates: Silead occasionally releases updates to address stability or improve touch accuracy. Check their official support page for patches.

Step 5: Disable Driver Signature Enforcement (Temporary)

If you keep getting "The hash of the file is not present in the specified catalog," restart Windows, press F8 (or Shift+Restart), select Disable Driver Signature Enforcement, then install the driver.

The Product: A Versatile Bridge Chip (198a)

The PID 198a maps to a highly flexible USB 2.0 to multi-interface bridge controller. Unlike a standard FTDI chip (which only does serial), the 198a is a composite device. This means it can present itself to your PC as several different things at once:

1. A CDC Serial Port (Virtual COM port for debugging).
2. A JTAG/SWD interface (For programming microcontrollers).
3. A SPI/I2C bridge (For flashing EEPROMs or sensors).

Common Hardware containing VID 1E3D PID 198A:

You will most likely find this chip inside one of the following devices:

• Generic ESP32 / ESP8266 Development Boards: Many low-cost NodeMCU or Wemos D1 clones use the CH340 (WCH) or CP2102 (Silicon Labs). However, a subset of mid-tier boards and wireless debuggers use the Chipsailing 198a to handle USB-to-UART conversion.
• FPGA Debugger Probes: Some Chinese-manufactured Intel/Altera or Lattice FPGA programmers (clones of the USB Blaster) utilize this chip.
• Custom Sensor Hubs: Industrial data loggers that aggregate temperature, humidity, or pressure sensors sometimes use this as the data concentrator.