Xinje Plc Usb Driver Install ((better))
English

Xinje Plc Usb Driver Install ((better))

Introduction

Xinjie PLC is a programmable logic controller (PLC) widely used in industrial automation applications. To communicate with a computer, the Xinjie PLC requires a USB driver to be installed on the computer. In this paper, we will guide you through the step-by-step process of installing the Xinjie PLC USB driver.

Hardware and Software Requirements

Before installing the Xinjie PLC USB driver, ensure that you have the following hardware and software:

Pre-Installation Steps

Before installing the driver, follow these pre-installation steps:

  1. Connect the Xinjie PLC to the computer: Connect the Xinjie PLC to the computer using the USB cable. Make sure the PLC is powered on.
  2. Check the Device Manager: Open the Device Manager on your computer (Windows key + X and select Device Manager). Check if the Xinjie PLC is listed under "Other devices" or "Unknown devices". If it is, note down the device name and VID (Vendor ID) and PID (Product ID).
  3. Download the driver software: Download the Xinjie PLC USB driver software from the manufacturer's website. Save the software to a folder on your computer.

Installing the Xinjie PLC USB Driver

To install the Xinjie PLC USB driver, follow these steps: xinje plc usb driver install

Method 1: Installing using the manufacturer's installation package

  1. Run the installation package: Run the downloaded installation package (it should be an executable file, e.g., "setup.exe").
  2. Follow the installation wizard: Follow the installation wizard to install the driver software. The wizard will guide you through the installation process.
  3. Select the device: When prompted, select the Xinjie PLC device from the list of detected devices.
  4. Complete the installation: Complete the installation process. The driver software will be installed, and the Xinjie PLC will be recognized by the computer.

Method 2: Installing using Windows Update

  1. Connect the Xinjie PLC to the computer: Connect the Xinjie PLC to the computer using the USB cable.
  2. Open Device Manager: Open the Device Manager on your computer (Windows key + X and select Device Manager).
  3. Update driver: Right-click on the Xinjie PLC device listed under "Other devices" or "Unknown devices" and select "Update driver".
  4. Search for updates: Select "Search automatically for updated driver software".
  5. Install the driver: Windows will search for and install the driver software. The Xinjie PLC will be recognized by the computer.

Verifying the Installation

After installing the driver, verify that the installation was successful:

  1. Open Device Manager: Open the Device Manager on your computer.
  2. Check the device list: Check that the Xinjie PLC is listed under "Ports (COM & LPT)" or "Universal Serial Bus controllers".
  3. Verify the COM port: Verify that the Xinjie PLC has been assigned a COM port (e.g., COM3, COM4, etc.).

Troubleshooting

If you encounter issues during installation, try the following troubleshooting steps:

Conclusion

In this paper, we have provided a step-by-step guide on installing the Xinjie PLC USB driver. By following these steps, you should be able to successfully install the driver and communicate with the Xinjie PLC using a computer. If you encounter any issues, refer to the troubleshooting section or contact the manufacturer's technical support.

Installing a Xinje PLC USB driver is the "handshake" that lets your PC talk to your industrial hardware. Whether you're using a direct USB cable or a USB-XC programming cable , follow this guide to bridge the gap. 1. Identify Your Cable and Controller Xinje PLCs usually connect in one of two ways: Direct USB Port: Newer models (like the ) often have a built-in USB port. USB-to-Serial Cable: Many older or slim models (XC series) require a specialized USB-XC programming cable . This cable typically uses a or similar chip to convert USB to RS232. 2. Download the Driver Do not rely on Windows to find the driver automatically. Visit the official Xinje Download Center Look for the "USB driver" "USB-to-Serial" driver under the software or tools section.

If you are using a 3rd party programming cable, you may need the CH341 driver specifically. 3. Installation Steps Disconnect the PLC:

Unplug the USB cable from your PC before starting the installation to avoid "unidentified device" errors. Run the Installer: Right-click the driver installer ( ) and select "Run as Administrator." The "Success" Check:

Once the installation finishes, plug the cable back into your PC and the PLC. Device Manager Verification: Device Manager on your Windows PC. Expand the Ports (COM & LPT) You should see "USB-SERIAL CH341 (COMx)" "Xinje USB" without any yellow warning triangles. Note the COM Port Number (e.g., COM3). 4. Configure Your Software

After the driver is "live," you must point your programming software to the right gate: (for XC series) or XINJE Config Communication Settings Serial Port Settings Select the that matched the number you saw in Device Manager. "Test Communication" to confirm the link is active. Troubleshooting Tips Driver Signature Error:

If you are on Windows 10 or 11 and the driver won't install, you might need to temporarily disable driver signature enforcement in your Windows startup settings. Cable Sequence: Introduction Xinjie PLC is a programmable logic controller

Always connect the cable to the PC first, wait for the chime, and then connect to the PLC. for your particular Xinje PLC model? Download Center - Wuxi Xinje Electric Co., Ltd.

Here’s a concise review of the Xinje PLC USB driver installation process, based on common user experiences (for models like XC, XD, XL series).

Step 2: Disable Driver Signature Enforcement (Windows 10/11 Only)

This is the most common hurdle. By default, Windows blocks unsigned drivers. XINJE drivers are often signed, but older versions may not be.

Method (Windows 10/11):

  1. Hold Shift and click Restart from the Start menu.
  2. When the blue screen appears, go to Troubleshoot > Advanced Options > Startup Settings > Restart.
  3. After restart, press 7 or F7 to select “Disable driver signature enforcement”.
  4. Now proceed with installation.

Part 4: Configuring XINJE AutoShop for USB Communication

Driver installation means nothing if AutoShop cannot see it. Here’s how to link the software to the new COM port.

  1. Open XINJE AutoShop.
  2. Click on Tools > Communication Setup (or click the “PC-PLC” icon on the toolbar).
  3. In the dialog box:
    • Communication Interface: Select Serial (not Ethernet).
    • COM Port: Choose the exact COM number you saw in Device Manager (e.g., COM5).
    • Baud Rate: Default is 9600 or 115200 depending on PLC model. AutoShop usually auto-detects, but manually set to 115200 for newer XD series.
    • Data Bits: 8
    • Stop Bits: 1
    • Parity: None
  4. Click Test Communication. You should see “Connection Successful”.
  5. Click OK and you are now ready to upload/download programs.

Part 4: Step-by-Step Installation for XINJE XD Series (AutoShop)

The XD series works best with the AutoShop programming software, which includes its own USB driver.

Step 3: Connect the PLC

Safety Precaution